3.5. Pre-Partitioning for Multi-Boot Systems

Partitioning your disk simply refers to the act of breaking up your disk into sections. Each section is then independent of the others. It's roughly equivalent to putting up walls inside a house; if you add furniture to one room it doesn't affect any other room.

If you already have an operating system on your system (Amiga OS, Atari TOS, Mac OS, …) and want to stick Linux on the same disk, you will need to repartition the disk. Debian requires its own hard disk partitions. It cannot be installed on Windows or MacOS partitions. It may be able to share some partitions with other Linux systems, but that's not covered here. At the very least you will need a dedicated partition for the Debian root.

You can find information about your current partition setup by using a partitioning tool for your current operating system , such as HD SC Setup, HDToolBox, or SCSITool . Partitioning tools always provide a way to show existing partitions without making changes.

In general, changing a partition with a file system already on it will destroy any information there. Thus you should always make backups before doing any repartitioning. Using the analogy of the house, you would probably want to move all the furniture out of the way before moving a wall or you risk destroying it.

If your computer has more than one hard disk, you may want to dedicate one of the hard disks completely to Debian. If so, you don't need to partition that disk before booting the installation system; the installer's included partitioning program can handle the job nicely.

If your machine has only one hard disk, and you would like to completely replace the current operating system with Debian GNU/Linux, you also can wait to partition as part of the installation process (Section 6.3.2.1, “Partitioning Your Disks”), after you have booted the installation system. However this only works if you plan to boot the installer system from tapes, CD-ROM or files on a connected machine. Consider: if you boot from files placed on the hard disk, and then partition that same hard disk within the installation system, thus erasing the boot files, you'd better hope the installation is successful the first time around. At the least in this case, you should have some alternate means of reviving your machine like the original system's installation tapes or CDs.

If your machine already has multiple partitions, and enough space can be provided by deleting and replacing one or more of them, then you too can wait and use the Debian installer's partitioning program. You should still read through the material below, because there may be special circumstances like the order of the existing partitions within the partition map, that force you to partition before installing anyway.

In all other cases, you'll need to partition your hard disk before starting the installation to create partition-able space for Debian. If some of the partitions will be owned by other operating systems, you should create those partitions using native operating system partitioning programs. We recommend that you do not attempt to create Debian Linux partitions using another operating system's tools. Instead, you should just create the native operating system's partitions you will want to retain.

If you are going to install more than one operating system on the same machine, you should install all other system(s) before proceeding with Linux installation. Windows and other OS installations may destroy your ability to start Linux, or encourage you to reformat non-native partitions.

You can recover from these actions or avoid them, but installing the native system first saves you trouble.

If you currently have one hard disk with one partition (a common setup for desktop computers), and you want to multi-boot the native operating system and Debian, you will need to:

  1. Back up everything on the computer.

  2. Boot from the native operating system installer media such as CD-ROM or tapes.

  3. Use the native partitioning tools to create native system partition(s). Leave either a place holder partition or free space for Debian GNU/Linux.

  4. Install the native operating system on its new partition.

  5. Boot back into the native system to verify everything's OK, and to download the Debian installer boot files.

  6. Boot the Debian installer to continue installing Debian.

3.5.1. Partitioning in AmigaOS

If you are running AmigaOS, you can use the HDToolBox program to adjust your native partitions prior to installation.

3.5.2. Partitioning in Atari TOS

Atari partition IDs are three ASCII characters, use ``LNX'' for data and ``SWP'' for swap partitions. If using the low memory installation method, a small Minix partition is also needed (about 2 MB), for which the partition ID is ``MNX''. Failure to set the appropriate partition IDs not only prevents the Debian installation process from recognizing the partitions, but also results in TOS attempting to use the Linux partitions, which confuses the hard disk driver and renders the whole disk inaccessible.

There are a multitude of third party partitioning tools available (the Atari harddisk utility doesn't permit changing the partition ID); this manual cannot give detailed descriptions for all of them. The following description covers SCSITool (from Hard+Soft GmBH).

  1. Start SCSITool and select the disk you want to partition (Disk menu, item select).

  2. From the Partition menu, select either New to add new partitions or change the existing partition sizes, or Change to change one specific partition. Unless you have already created partitions with the right sizes and only want to change the partition ID, New is probably the best choice.

  3. For the New choice, select existing in the dialog box prompting the initial settings. The next window shows a list of existing partitions which you can adjust using the scroll buttons, or by clicking in the bar graphs. The first column in the partition list is the partition type; just click on the text field to edit it. When you are finished changing partition settings, save the changes by leaving the window with the OK button.

  4. For the Change option, select the partition to change in the selection list, and select other systems in the dialog box. The next window lists detailed information about the location of this partition, and lets you change the partition ID. Save changes by leaving the window with the OK button.

  5. Write down the Linux names for each of the partitions you created or changed for use with Linux — see Section A.4, “Device Names in Linux”.

  6. Quit SCSITool using the Quit item from the File menu. The computer will reboot to make sure the changed partition table is used by TOS. If you changed any TOS/GEM partitions, they will be invalidated and have to be reinitialized (we told you to back up everything on the disk, didn't we?).

There is a partitioning tool for Linux/m68k called atari-fdisk in the installation system, but for now we recommend you partition your disk using a TOS partition editor or some disk tool. If your partition editor doesn't have an option to edit the partition type, you can do this crucial step at a later stage (from the booted temporary install RAMdisk). SCSITool is only one of the partition editors we know of which supports selection of arbitrary partition types. There may be others; select the tool that suits your needs.

3.5.3. Partitioning in MacOS

Partitioning tools for Macintosh tested include pdisk, HD SC Setup 7.3.5 (Apple), HDT 1.8 (FWB), SilverLining (LaCie), and DiskTool (Tim Endres, GPL). Full versions are required for HDT and SilverLining. The Apple tool requires a patch in order to recognize third-party disks (a description on how to patch HD SC Setup using ResEdit can be found at http://www.euronet.nl/users/ernstoud/patch.html).

For IDE based Macs, you need to use Apple Drive Setup to create empty space for the Linux partitions, and complete the partitioning under Linux, or use the MacOS version of pdisk available from the MkLinux FTP server.